Ferroli Bravo 10L 2kW Under-Sink Unvented Electric Water Heater SN10SVE2.0U
The Ferroli Bravo 10L Under-Sink (MPN: SN10SVE2.0U) is a 10-litre unvented storage water heater delivering mains-pressure hot water at the point of use. Rated at 2 kW at 240 V with an IPX4 splash-proof rating, it is suited to under-sink installation in bathrooms, cloakrooms, and wet areas where a larger hot-water reserve than a 5-litre unit is required. Compatible with standard and thermostatic mixer taps — unlike vented heaters — the Bravo 10L ships with a reinforced hanging bracket, built-in cable, and 2-year warranty. Note: as an unvented unit, installation requires a G3 accredited competent person.
The Bravo 10L is an unvented water heater. Installation must be carried out by a G3 accredited competent person in accordance with Building Regulations Approved Document G3. All electrical connections must be completed by a qualified electrician to current IET Wiring Regulations.
The SN10SVE2.0U (this listing) is the under-sink variant — cold water enters from below, hot water discharges upward. The SN10SVE2.0 (without the U suffix) is the over-sink model where cold enters from above. Selecting the wrong model will result in incorrect water flow direction. If you are unsure, check with your installer before ordering.
Because the Bravo 10L is unvented (mains pressure), it can be used with standard shut-off taps and thermostatic mixer taps — no open-outlet spout tap is required. This makes it the right choice where a conventional or thermostatic basin mixer is being fitted alongside the heater.
As an unvented heater, the Bravo 10L stores water at mains pressure, delivering hot water to the tap at full mains flow rate — no loft tank, no pump. This makes it compatible with thermostatic and pressure-balancing mixer taps that require balanced hot and cold supplies, unlike vented (open-outlet) alternatives.
The 10-litre store provides approximately twice the hot water volume of the Novo 5L, supporting multiple hand-wash cycles or prolonged sink use between element top-ups. This is particularly valuable in busier cloakrooms, accessible toilets with higher footfall, or applications with frequent handwashing demand throughout the day.
IPX4 splash-proof protection allows installation in bathrooms, cloakrooms, shower rooms, and other wet areas, subject to current IET Wiring Regulations zone requirements. The shockproof ABS outer casing protects internal components from the accidental knocks typical in confined under-sink spaces.
A reinforced hanging bracket is supplied, allowing the Bravo 10L to be securely wall-mounted inside a vanity unit or directly to a wall under the sink. At 340 × 330 × 300 mm, the unit fits within most standard under-sink cabinet dimensions — measure your cabinet depth and width before ordering to confirm clearance.
A pre-fitted electrical cable (without plug) is included for connection to a dedicated fused spur. A user-adjustable thermostat allows temperature to be set to preference. The rust-free construction and easy-access design facilitate straightforward periodic servicing in the under-sink environment.
The Bravo range spans 10, 15, and 30 litre capacities, available in both under-sink and over-sink configurations, with element ratings from 2 kW to 3 kW. This allows a consistent Ferroli specification across multiple washroom locations within the same building. Contact us for other Bravo variants and matching open-outlet tap accessories.
| Parameter | Bravo 10L Under-Sink Specification |
|---|---|
| MPN | SN10SVE2.0U |
| Type | Unvented storage — under-sink point-of-use |
| Capacity | 10 litres |
| Power | 2 kW @ 240 V AC |
| Dimensions H × W × D | 340 × 330 × 300 mm |
| IP rating | IPX4 |
| Casing material | Shockproof ABS |
| Installation orientation | Under-sink (U-suffix model) |
| Pressure type | Unvented — mains pressure |
| G3 certification required | Yes — unvented unit |
| Compatible tap types | Standard shut-off taps; thermostatic mixer taps |
| Hanging bracket | Reinforced bracket supplied |
| Built-in cable | Yes (without plug) |
| Temperature adjustment | Yes — adjustable thermostat |
| Casing | Rust-free / shockproof ABS |
| Warranty | 2 years |
More Images
Ferroli Bravo 10L 2kW Under-Sink Unvented Electric Water Heater SN10SVE2.0U
The Ferroli Bravo 10L Under-Sink (MPN: SN10SVE2.0U) is a 10-litre unvented storage water heater delivering mains-pressure hot water at the point of use. Rated at 2 kW at 240 V with an IPX4 splash-proof rating, it is suited to under-sink installation in bathrooms, cloakrooms, and wet areas where a larger hot-water reserve than a 5-litre unit is required. Compatible with standard and thermostatic mixer taps — unlike vented heaters — the Bravo 10L ships with a reinforced hanging bracket, built-in cable, and 2-year warranty. Note: as an unvented unit, installation requires a G3 accredited competent person.
The Bravo 10L is an unvented water heater. Installation must be carried out by a G3 accredited competent person in accordance with Building Regulations Approved Document G3. All electrical connections must be completed by a qualified electrician to current IET Wiring Regulations.
The SN10SVE2.0U (this listing) is the under-sink variant — cold water enters from below, hot water discharges upward. The SN10SVE2.0 (without the U suffix) is the over-sink model where cold enters from above. Selecting the wrong model will result in incorrect water flow direction. If you are unsure, check with your installer before ordering.
Because the Bravo 10L is unvented (mains pressure), it can be used with standard shut-off taps and thermostatic mixer taps — no open-outlet spout tap is required. This makes it the right choice where a conventional or thermostatic basin mixer is being fitted alongside the heater.
As an unvented heater, the Bravo 10L stores water at mains pressure, delivering hot water to the tap at full mains flow rate — no loft tank, no pump. This makes it compatible with thermostatic and pressure-balancing mixer taps that require balanced hot and cold supplies, unlike vented (open-outlet) alternatives.
The 10-litre store provides approximately twice the hot water volume of the Novo 5L, supporting multiple hand-wash cycles or prolonged sink use between element top-ups. This is particularly valuable in busier cloakrooms, accessible toilets with higher footfall, or applications with frequent handwashing demand throughout the day.
IPX4 splash-proof protection allows installation in bathrooms, cloakrooms, shower rooms, and other wet areas, subject to current IET Wiring Regulations zone requirements. The shockproof ABS outer casing protects internal components from the accidental knocks typical in confined under-sink spaces.
A reinforced hanging bracket is supplied, allowing the Bravo 10L to be securely wall-mounted inside a vanity unit or directly to a wall under the sink. At 340 × 330 × 300 mm, the unit fits within most standard under-sink cabinet dimensions — measure your cabinet depth and width before ordering to confirm clearance.
A pre-fitted electrical cable (without plug) is included for connection to a dedicated fused spur. A user-adjustable thermostat allows temperature to be set to preference. The rust-free construction and easy-access design facilitate straightforward periodic servicing in the under-sink environment.
The Bravo range spans 10, 15, and 30 litre capacities, available in both under-sink and over-sink configurations, with element ratings from 2 kW to 3 kW. This allows a consistent Ferroli specification across multiple washroom locations within the same building. Contact us for other Bravo variants and matching open-outlet tap accessories.
| Parameter | Bravo 10L Under-Sink Specification |
|---|---|
| MPN | SN10SVE2.0U |
| Type | Unvented storage — under-sink point-of-use |
| Capacity | 10 litres |
| Power | 2 kW @ 240 V AC |
| Dimensions H × W × D | 340 × 330 × 300 mm |
| IP rating | IPX4 |
| Casing material | Shockproof ABS |
| Installation orientation | Under-sink (U-suffix model) |
| Pressure type | Unvented — mains pressure |
| G3 certification required | Yes — unvented unit |
| Compatible tap types | Standard shut-off taps; thermostatic mixer taps |
| Hanging bracket | Reinforced bracket supplied |
| Built-in cable | Yes (without plug) |
| Temperature adjustment | Yes — adjustable thermostat |
| Casing | Rust-free / shockproof ABS |
| Warranty | 2 years |
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
The Ferroli Bravo 10L Under-Sink (MPN: SN10SVE2.0U) is a 10-litre unvented storage water heater delivering mains-pressure hot water at the point of use. Rated at 2 kW at 240 V with an IPX4 splash-proof rating, it is suited to under-sink installation in bathrooms, cloakrooms, and wet areas where a larger hot-water reserve than a 5-litre unit is required. Compatible with standard and thermostatic mixer taps — unlike vented heaters — the Bravo 10L ships with a reinforced hanging bracket, built-in cable, and 2-year warranty. Note: as an unvented unit, installation requires a G3 accredited competent person.
The Bravo 10L is an unvented water heater. Installation must be carried out by a G3 accredited competent person in accordance with Building Regulations Approved Document G3. All electrical connections must be completed by a qualified electrician to current IET Wiring Regulations.
The SN10SVE2.0U (this listing) is the under-sink variant — cold water enters from below, hot water discharges upward. The SN10SVE2.0 (without the U suffix) is the over-sink model where cold enters from above. Selecting the wrong model will result in incorrect water flow direction. If you are unsure, check with your installer before ordering.
Because the Bravo 10L is unvented (mains pressure), it can be used with standard shut-off taps and thermostatic mixer taps — no open-outlet spout tap is required. This makes it the right choice where a conventional or thermostatic basin mixer is being fitted alongside the heater.
As an unvented heater, the Bravo 10L stores water at mains pressure, delivering hot water to the tap at full mains flow rate — no loft tank, no pump. This makes it compatible with thermostatic and pressure-balancing mixer taps that require balanced hot and cold supplies, unlike vented (open-outlet) alternatives.
The 10-litre store provides approximately twice the hot water volume of the Novo 5L, supporting multiple hand-wash cycles or prolonged sink use between element top-ups. This is particularly valuable in busier cloakrooms, accessible toilets with higher footfall, or applications with frequent handwashing demand throughout the day.
IPX4 splash-proof protection allows installation in bathrooms, cloakrooms, shower rooms, and other wet areas, subject to current IET Wiring Regulations zone requirements. The shockproof ABS outer casing protects internal components from the accidental knocks typical in confined under-sink spaces.
A reinforced hanging bracket is supplied, allowing the Bravo 10L to be securely wall-mounted inside a vanity unit or directly to a wall under the sink. At 340 × 330 × 300 mm, the unit fits within most standard under-sink cabinet dimensions — measure your cabinet depth and width before ordering to confirm clearance.
A pre-fitted electrical cable (without plug) is included for connection to a dedicated fused spur. A user-adjustable thermostat allows temperature to be set to preference. The rust-free construction and easy-access design facilitate straightforward periodic servicing in the under-sink environment.
The Bravo range spans 10, 15, and 30 litre capacities, available in both under-sink and over-sink configurations, with element ratings from 2 kW to 3 kW. This allows a consistent Ferroli specification across multiple washroom locations within the same building. Contact us for other Bravo variants and matching open-outlet tap accessories.
| Parameter | Bravo 10L Under-Sink Specification |
|---|---|
| MPN | SN10SVE2.0U |
| Type | Unvented storage — under-sink point-of-use |
| Capacity | 10 litres |
| Power | 2 kW @ 240 V AC |
| Dimensions H × W × D | 340 × 330 × 300 mm |
| IP rating | IPX4 |
| Casing material | Shockproof ABS |
| Installation orientation | Under-sink (U-suffix model) |
| Pressure type | Unvented — mains pressure |
| G3 certification required | Yes — unvented unit |
| Compatible tap types | Standard shut-off taps; thermostatic mixer taps |
| Hanging bracket | Reinforced bracket supplied |
| Built-in cable | Yes (without plug) |
| Temperature adjustment | Yes — adjustable thermostat |
| Casing | Rust-free / shockproof ABS |
| Warranty | 2 years |
